Open 24/7 · Greater Los Angeles & Ventura County

(323) 997-8867
Crenshaw Lock

Commercial Door Hardware in Palmdale · 24/7 mobile

Commercial Door Hardware Repair and Replacement in Palmdale, CA

Crenshaw Lock Company provides 24/7 mobile commercial door hardware repair and replacement in Palmdale, California, covering storefront, aluminum-frame and mortise hardware. We come to your business, diagnose the door, and fix or replace what is failing. Call (323) 997-8867 any time, day or night.

  • Mobile to your Palmdale location
  • Available 24/7
  • Price quoted before we start
Call (323) 997-8867or tap to call — we answer 24/7
Aluminum storefront door with mortise lock and pull handle
Open now(323) 997-8867

A commercial door is used far more than a house door. It opens and closes hundreds of times a day, gets pushed by carts and deliveries, and is expected to lock reliably every night. In Palmdale, add the Antelope Valley sun, wind, and dust, and hardware wears out faster than most owners expect. Closers lose their speed, latches stop catching, thumb-turns seize, and panic devices start to stick. Often the problem is a worn part, not a failed door.

Crenshaw Lock Company has served Greater Los Angeles and Ventura County since 1987, and owner and lead technician David Shar has worked on every common type of commercial hardware in that time. We are fully mobile, so there is no storefront to visit. We bring tools, parts, and experience to your suite, shop, or warehouse and work on the door where it hangs.

This page covers the hardware we repair and replace most for Palmdale businesses: aluminum-frame storefront doors with narrow stiles, mortise locksets in older commercial buildings, exit devices, closers, and the cylinders and keying that tie them together. If a door is failing at night or leaves your building unsecured, call (323) 997-8867. We are available 24/7.

How it works in Palmdale

  1. 1

    Describe the problem by phone

    Call (323) 997-8867 and tell us what the door is doing: not latching, key sticking, closer slamming, handle loose, or the building not locking at all. Mention the door type if you know it, such as aluminum storefront, hollow metal, or wood with a mortise lock. That helps us bring the right parts.

  2. 2

    On-site inspection of the door and frame

    We check the hardware, but also the things that cause hardware to fail: door sag, hinge wear, frame misalignment, a strike plate out of position, or a closer fighting the door. Replacing a lock on a door that drags only buys a short repair, so we look at the whole opening.

  3. 3

    Repair or replace, explained plainly

    Many commercial locks can be serviced, rebuilt, or adjusted. Others are worn out or no longer made. We explain which situation you have and what each choice means for security, compliance, and long-term cost, before work begins.

  4. 4

    Hardware work and re-keying

    We repair or install storefront locks, mortise lock bodies, cylinders, exit devices, closers, and strike hardware. If keys have been lost or an employee has left, we can rekey cylinders or set up master-key and restricted-key arrangements that match how your business actually operates.

  5. 5

    Function and security test

    Before we finish we cycle the door repeatedly, check latch engagement, test every key, and confirm the door closes and locks on its own where it should. We want the building secure when we drive away.

Need commercial door hardware in Palmdale?

24/7 Mobile Locksmith across Greater Los Angeles & Ventura County. We answer 24/7.

Call (323) 997-8867

What affects the price

  • Type of hardware involved: a simple cylinder swap is a different job than a mortise lock body, exit device, or full storefront lock replacement.
  • Condition of the door and frame, since sagging, bent, or misaligned aluminum may need adjustment or additional parts before new hardware will work.
  • Whether the hardware is standard or specialty, as discontinued or manufacturer-specific parts for older storefronts can take more effort to source.
  • Keying requirements, including how many cylinders are rekeyed, and whether you want master-key or restricted-key systems.
  • Time and urgency of the call, including after-hours or emergency visits to secure a building that cannot lock.
  • Number of doors in the visit, since several openings handled at once are usually more efficient than separate trips.

Why Palmdale chooses us

  • Fully mobile service: we work at your door in Palmdale, with no shop to drive to and no need to remove a door and leave the building open.
  • Experience since 1987 with older and newer commercial hardware, including mortise locks that many general handymen avoid.
  • Owner involvement: David Shar leads the work, so you are dealing with a locksmith, not a call center.
  • We look at the entire opening, not just the lock, which helps prevent repeat failures from sagging doors or poorly set closers.
  • Straight advice on repair versus replacement, so you do not pay for new hardware when a rebuild would do, or patch hardware that is truly finished.
  • 24/7 availability for lockouts, broken locks, and doors that will not secure after a break-in or damage.

Commercial Door Hardware across Palmdale

Palmdale's commercial doors face conditions that are hard on hardware. Summer heat in the high desert expands aluminum frames and bakes closers and keypad locks, while wind and fine dust work into latches and cylinders. Businesses near the Antelope Valley Mall and along Palmdale Blvd, Avenue S, and Sierra Highway often have aluminum storefront doors with narrow-stile locks that wear out from constant use. We see heat-affected keypad locks, loose handles, and closers that no longer control the door.

The Plant 42 corridor and the industrial areas around Air Force Plant 42 and Palmdale Regional Airport bring a different set of needs: master-key and restricted-key systems, controlled access, and doors that must be secure after hours. In Downtown Palmdale, older buildings may still carry mortise locks that can be serviced instead of replaced. We also work with businesses serving Rancho Vista, Anaverde, City Ranch, and Quartz Hill, as well as owners along CA-14 and CA-138.

Whether your business is in ZIP 93550 near downtown, 93551 on the west side, 93552 toward the east, or 93591 out toward Lake Los Angeles, we come to you. Call (323) 997-8867 and we will talk through the door, the hardware, and the best way to get it working.

Locked out or need a locksmith now?

24/7 Mobile Locksmith across Greater Los Angeles & Ventura County. We answer 24/7.

Call (323) 997-8867

Other Palmdale locksmith services

See all of our Palmdale services, or our citywide commercial door hardware page.

Commercial Door Hardware in Palmdale — FAQs

Do you repair aluminum storefront door hardware in Palmdale?
Yes. We repair and replace locks, latches, pull handles, closers, and cylinders on aluminum-frame storefront doors. Call (323) 997-8867 and describe the door so we can bring appropriate parts.
Can you work on older mortise locks?
Yes. Many older commercial buildings in Palmdale still use mortise locksets. We can often service or rebuild them, and we will tell you honestly when replacement makes more sense.
Are you available after hours if my business cannot lock?
Yes. We are available 24/7 and fully mobile. If a door will not secure at night, call (323) 997-8867 and we will help get your building locked.
Can you set up master-key or restricted-key systems?
Yes. We can rekey cylinders and arrange master-key systems for multiple doors, and restricted-key options where you want tighter control over who can copy keys.
Why does my storefront door keep failing even after new hardware?
The cause is often the door itself: sag, worn hinges, a misaligned strike, or a closer that is pulling or slamming the door. We check the whole opening so the repair lasts.
Does Palmdale's heat affect commercial locks?
It can. High-desert sun and heat can stress closers, aluminum frames, and electronic or keypad locks, and dust can foul latches and cylinders. Regular adjustment and the right hardware choices help.
Do you have a shop I can visit?
No. Crenshaw Lock Company is mobile only. We come to your Palmdale location and do the work on site.
How do I get a price for commercial door hardware work?
Pricing depends on the hardware, door condition, keying, number of doors, and timing. Call (323) 997-8867, describe the situation, and we will explain what affects the cost before work starts.
DS

Reviewed by David Shar — Owner & Lead Technician

Crenshaw Lock Company has served Greater Los Angeles & Ventura County since 1987.

Last updated 2026-10-12.

Call (323) 997-8867 · Open 24/7