Open 24/7 · Greater Los Angeles & Ventura County

(323) 997-8867
Crenshaw Lock

Commercial Door Hardware in Culver City · 24/7 mobile

Commercial Door Hardware in Culver City, CA

Crenshaw Lock Company repairs and replaces commercial door hardware in Culver City, including storefront, aluminum-frame and mortise hardware. We are fully mobile and available 24/7, so we come to your business. Call (323) 997-8867 to describe the door and get a technician headed your way.

  • Mobile to your Culver City location
  • Available 24/7
  • Price quoted before we start
Call (323) 997-8867or tap to call — we answer 24/7
Aluminum storefront door with mortise lock and pull handle
Open now(323) 997-8867

A commercial door works harder than almost anything else in a building. A storefront on Washington Boulevard may open and close hundreds of times a day, and a tired closer, a loose panic bar or a worn deadbolt throw can turn into a security problem or a failed fire-code check long before the door looks broken. Crenshaw Lock Company has serviced doors across Greater Los Angeles and Ventura County since 1987, and commercial hardware is a regular part of that work.

Culver City has an unusual mix of buildings. Aluminum-frame storefronts line the main commercial corridors, studio and office buildings fill the Hayden Tract and downtown, and older properties still carry original mortise hardware from the 1920s through the 1940s. Each of these takes different parts, different tools and a different approach. Narrow-stile aluminum doors need hardware sized to the frame, while mortise locks need the right case, trim and strike to match what is already cut into the door.

We are mobile only. There is no shop to drive to, because the work is done at your door, whether that is a retail entrance, a production office, a stairwell or a back-of-house exit. David Shar leads the work, and we are available day and night when a door will not lock or will not open.

How it works in Culver City

  1. 1

    Describe the door and the problem

    Call (323) 997-8867 and tell us what the door is: aluminum storefront, hollow metal, wood with a mortise lock, or glass. Tell us what is failing, such as a latch that sticks, a cylinder that will not turn, a closer that slams, or an exit device that does not retract.

  2. 2

    On-site inspection of the whole assembly

    We check more than the part that is complaining. A lock that binds is often caused by a sagging door, a misaligned strike or a worn hinge. We test the latch, deadbolt, closer, exit device and frame so we fix the cause and not only the symptom.

  3. 3

    Repair or replace, explained plainly

    Some hardware can be adjusted, rebuilt or re-cylindered. Some is worn out or no longer made. We explain which is which and what each choice means for security, code compliance and the look of the entrance before any work starts.

  4. 4

    Fit, adjust and test

    We install or repair the hardware and fit it to the door, including strike alignment, backset, throw length and closer speed. We then cycle the door repeatedly, from the inside and outside, to confirm it latches and releases properly.

  5. 5

    Keys, rekeying and follow-up

    If the repair involves cylinders, we can rekey to your existing system, set up a master-key structure, or work with high-security cylinders where your tenant requires them. You leave with working keys and a door you can lock behind you.

Need commercial door hardware in Culver City?

24/7 Mobile Locksmith across Greater Los Angeles & Ventura County. We answer 24/7.

Call (323) 997-8867

What affects the price

  • The type of hardware involved: a standard storefront deadbolt differs from a mortise lock body, a rim exit device or a high-security cylinder.
  • Whether the existing hardware can be repaired or rebuilt, or the part is worn or discontinued and the unit must be replaced.
  • The door and frame material and condition, since narrow-stile aluminum, hollow metal and old wood doors each need different parts and labor.
  • How many doors are included and whether they need to be keyed alike or fit into a master-key system.
  • Whether access control, electric strikes or other electronics are tied into the hardware.
  • The time of the call, since after-hours and emergency work involves different scheduling than a planned daytime visit.

Why Culver City chooses us

  • We have been serving Los Angeles and Ventura County businesses since 1987, so older mortise and storefront hardware is familiar territory.
  • We are fully mobile and available 24/7, which matters when a storefront will not secure at closing time.
  • We look at the entire door assembly, not only the lock, so repairs hold up instead of failing again at the next sticking point.
  • We can match existing keying or build a master-key system, including high-security cylinder platforms such as Medeco and Schlage Primus when a tenant specifies them.
  • We explain the repair-versus-replace choice honestly and do not push a full replacement when an adjustment will do.

Commercial Door Hardware across Culver City

Culver City's commercial doors vary a lot from block to block. Downtown, around the Culver Hotel, the Kirk Douglas Theatre and The Culver Steps, you find a mix of historic entrances and newer mixed-use storefronts. The Helms Bakery District and the Hayden Tract carry converted creative offices and tech-tenant buildings, where aluminum-frame glass doors and controlled-access entries are common. Along Washington Boulevard, Culver Boulevard and Sepulveda Boulevard, retail and service businesses rely on storefront hardware that sees steady daily use.

Production offices and tech tenants often need more than a simple repair. A rekey or master-key setup for a suite in the Hayden Tract or downtown may involve high-security cylinders or tie into electronic access control, and we plan the hardware around that. Properties near Sony Pictures Studios and Culver Studios in ZIP code 90232 often need controlled keying so different departments and vendors have the right level of access.

Older buildings bring their own needs. Spanish bungalows and Craftsman cottages in Carlson Park, and some small commercial conversions nearby, can still have original 1920s to 1940s mortise hardware that is worth keeping working. In Fox Hills, large condo and apartment buildings in ZIP code 90230 have common-area doors, entries and amenity rooms that property managers need serviced and rekeyed, especially after tenant turnover. Whether you are near Westfield Culver City, off Jefferson Boulevard or close to the I-405, we come to you.

Locked out or need a locksmith now?

24/7 Mobile Locksmith across Greater Los Angeles & Ventura County. We answer 24/7.

Call (323) 997-8867

Other Culver City locksmith services

See all of our Culver City services, or our citywide commercial door hardware page.

Commercial Door Hardware in Culver City — FAQs

Do you repair aluminum storefront door hardware in Culver City?
Yes. We repair and replace hardware on aluminum-frame storefront doors, including deadbolts, latches, pull handles, closers and exit devices. Call (323) 997-8867 and tell us about the door so we can bring the right parts.
Can you work on old mortise locks?
Yes. Mortise hardware is common in older Culver City buildings. We can often service or rebuild an original mortise lock, and when that is not practical we help find a suitable replacement that fits the existing door preparation.
Are you available after hours or overnight?
We are available 24/7. If your storefront will not lock or an exit door is jammed, call (323) 997-8867 at any hour. We are mobile, so we come to your location.
Do I need to bring the door to a shop?
No. Crenshaw Lock is fully mobile with no storefront to visit. We do the repair at your door, which is especially useful for glass and aluminum entrances that cannot be removed easily.
Can you set up a master-key system for an office or production space?
Yes. We can plan keying so that different doors, departments or tenants have appropriate access levels. We can also work with high-security cylinders when your building or tenant requires them.
Will you tell me whether to repair or replace?
Yes. After inspecting the door, we explain whether adjustment or repair is enough or whether the hardware has worn out. You decide before work begins.
Can you work with electronic access control or electric strikes?
We can service the mechanical hardware that those systems depend on and can coordinate with electric strikes and other electronic components. Describe your setup when you call (323) 997-8867 so we can plan the visit.
Do you handle property-managed buildings like those in Fox Hills?
Yes. We can service common-area doors and rekey after tenant turnover, coordinating with property management so access and keys are handled cleanly.
DS

Reviewed by David Shar — Owner & Lead Technician

Crenshaw Lock Company has served Greater Los Angeles & Ventura County since 1987.

Last updated 2026-10-12.

Call (323) 997-8867 · Open 24/7